Ranking of the best medical devices for cleaning and lubricating handpieces for 2020

Medical instrument tips can wear out quickly. One of the main reasons for their failure is improper care. According to statistics, about 75% of the handpieces became unusable for this reason.

What equipment is needed to clean and lubricate medical handpieces

To keep medical handpieces in good working order, they must be regularly cleaned and lubricated using a special apparatus. It helps to remove absolutely all dirt, thoroughly lubricates the handpieces and prepares them for subsequent use.

What the device does:

1. This device is primarily used for cleaning handpieces. It is able to remove a variety of contaminants even in the most inaccessible places This is possible thanks to special cleaning agents and advanced technologies that are used during the operation of the device.
2. The device is capable of providing high-quality disinfection of equipment. This fact is very important, because the hygienic state of any medical instrument must meet all existing requirements.

It is worth noting the fact that cleaning of many equipment, including medical handpieces, takes a lot of time. The thing is that such devices have many areas that are difficult to reach. Cleaning them by hand is very tedious, so the desire to simplify and improve this process is justified.

Today there are a huge number of companies that specialize in the manufacture of devices for cleaning medical handpieces. They differ from each other in many parameters, including:

1. Sizes. These devices can be of different sizes. The market is overcrowded with both compact and very large devices. Sufficiently large devices are capable of simultaneously processing a large number of tools, while compact ones will process only a few units.
2. Performance. Device performance depends on several factors. One of them is the number of tools that can be processed simultaneously.
3. Manufacturability. Modern manufacturers strive to improve equipment as much as possible. Each of them is trying to make their own additions to the operation of the device and to do everything possible so that the result obtained is the best possible.

Turbine and mechanical handpieces: general guidelines

Today, the devices in question are used in all medical institutions.

Disinfection

Cleaning and sterilization of NSK turbines can be carried out with a thermal disinfector.After thermal disinfection, the device is used taking into account all the recommendations given by the manufacturer.

Autoclaving (sterilization)

All types of handpieces can be autoclaved, but only subject to preliminary preparation. After sterilization, it is extremely difficult to remove dirt from the instrument. This fact cannot be ignored. It is worth noting the fact that oils retain all their properties even after sterilization.

The main advantages

The operational life of any medical equipment directly depends on how well it is looked after. This fact forces manufacturers to pay special attention to improving existing technology and to find methods for sterilizing and cleaning instruments that will not be able to have any negative impact on them. At the same time, specific solutions are applied for each area of ​​medicine. For example, when processing the handpieces of instruments used in dentistry, it is important to keep in mind that they need to be pre-cleaned and lubricated. If you neglect this rule, sterilization cannot be called safe.

To carry out such procedures, separate devices have been created. They clean the interior and lubricate the handpieces. These devices have many advantages, including:

1. Ability to extend tool life.
2. Significant reduction in repair costs.
3. Fast tool cleaning.
4. Cleaning of all types of handpieces.
5. Full automation. The device automatically performs all the necessary operations.
6. Easy to use.
7. Good performance.
8. Low consumption of oils used to lubricate the tool.
9. Safety of processed tools.

When choosing a device, pay attention to:

• cycle time;
• types of tips that can be placed in the cleaning device;
• device price;
• the experience of the company that produces it;
• the amount of oil consumed;
• the need for compressed gas.

Best cleaning devices: rating

For the care of medical handpieces, special disinfection and lubrication autoclaving equipment is ideal. It is able in one cycle not only to remove contaminants that are on the surface and in the internal channels, but also lubricate and sterilize the instrument. Often, such devices can handle handpieces of any company. However, their price is quite high. In one working cycle, which lasts about 40 minutes, the device can process no more than 6 handpieces. At a time when simpler devices can perform only one operation - cleaning, rinsing or lubrication.

Assistina 301 Plus

This model is considered the most optimal option. The device is fully automated and has a number of advantages - ease of use, device reliability and economy.

The Assistina 301 Plus is air-driven and is suitable for the care of:

• handpieces of straight and angle type;
• turbines;
• instruments used to remove tartar;
• pneumatic motors.

This device should be used only after preliminary treatment, namely, removal of contaminants from the surface of the instrument and disinfection. Such events allow creating optimal conditions for the processing and storage of medical instruments.

Assistina 301 Plus can be called a unique device that has no analogues. It helps to save a lot of costs per treatment and pays off within a year after you start using it.

• the ability to increase the operating period of a tool that undergoes regular processing;
• no need for regular repairs and maintenance. This is possible through the use of;
• W&H oil and its optimal distribution;
• the ability to separate dirt from the surface of the tool, and then remove. This guarantees minimal friction, minimal wear and increased tool life;
• economical use of oil;
• the use of a special, alcohol solution for flushing the spray channels;
• preventing the appearance of lime accumulations, which is possible due to the blowing of the channels with compressed air.

• not found.

This device has earned the title of one of the best, thanks to the ability to clean and lubricate tools efficiently. The manufacturer was able to achieve this result thanks to the introduction of a new care system. It is fully automated and performs all tasks perfectly.

KaVo QUATTROcare® Plus 2124A

QUATTROcare PLUS 2124A is used for processing instruments such as:

• turbine and contra-angle handpieces;
• heads.

This device managed to prove itself and take one of the leading positions. It is used to process all types of handpieces and is capable of performing it efficiently, quickly and reliably.

The device is capable of performing additional purging of spray channels and removing excess oil from the surface of the handpieces, but only if it is connected to a compressed air source.

The tools that are produced by this company have established themselves as the highest quality and durable. However, statistics show that more than 50% of breakdowns occur due to contamination. This device will perform the best cleaning, and the automated system will adjust the amount of oil supplied, which can ensure proper lubrication of the tool.

• high quality of the device;
• the ability to supplement the device with adapters that allow you to process a variety of tools;
• the ability to independently control and regulate the oil supply;
• simple use;
• the ability to process up to 4 tools in 1 minute;
• you can connect an adapter for the device;
• the ability to reduce or increase the amount of oil supplied to tools during lubrication;
• ease of use.

• not found.

Assistina 3 × 2

This device can be called one of the most efficient. It is equipped with an air drive that automatically cleans and lubricates all types of handpieces, air motors, calculus removers and surgical handpieces. The only exceptions to this rule are air bearing turbine tools.

This device is fully automated. He independently performs all the preparatory work that must be done before placing the instrument in the autoclave. It makes cleaning the handpieces much easier and faster.

Assistina 3 × 2 is able to thoroughly clean any tool and ensure its normal operation throughout its entire operating life.

• Simple to use. This device is equipped with a clear interface that is perceived at an intuitive level. No training is required to operate this machine. You can start it by pressing one button.
• Correct lubrication. Instruments are lubricated automatically, and the use of F1 oil significantly increases the service life of medical instruments.
• Fast cycle. The complete cycle is about 6 minutes. After this time, the instrument is ready to be placed in the autoclave.
• Nice price. This device is distinguished by its affordable price, but this does not affect its quality in any way. It is able to clean medical instruments as efficiently as possible, despite the minimum purchase cost.
• Quality assurance. Experts confirm the fact that this device is able to clean the instrument efficiently. The confirmation sticker is located in the loading chamber.

• not found.

NSK Care3 Plus C1

This machine can accommodate high and low speed handpieces at the same time. It not only cleans but also lubricates tools. At the same time, its daily use helps to extend the life of the handpieces.

One of the most important benefits of NSK Care3 Plus C1 is the integrity of the cleaning and lubrication process.The device rotates the handpieces. During this time, a special solution and lubricating oil penetrate all the holes of the handpieces. This guarantees high-quality processing of the tools.

This instrument is perfect for low speed handpieces. The system port of the instrument rotates the gear mechanism inside the handpiece, which allows for good cleaning and thorough lubrication.

• convenient use of the device;
• the ability to rotate the mechanisms located inside the tip, which improves the quality of cleaning;
• fast cleaning;
• cost savings;
• safety;
• rotation with filtered air;
• an indicator that allows you to control the level of the solution;
• oil filter system;
• the presence of air purge, which allows you to remove the remaining solution from the surface of the tips;
• easy cleaning at the end of use.

• not found.

Woson LUB909

Woson LUB909 is analogous to NSK Care3 Plus. It is capable of cleaning and lubricating up to 3 instruments in one cycle.

This device is designed to prepare handpieces for autoclaving. One of its main features and distinguishing characteristics is the simplified filling of the container with oil and the presence of a removable panel that makes it easy to clean the device.

• the ability to use it for cleaning and lubricating handpieces used in dentistry;
• the ability to process 3 tools in one cycle;
• the presence of a swivel mechanism that allows you to clean and lubricate the tips at different angles;
• the ability to adjust the processing modes, depending on the tool being processed. A short, long or very long mode can be set.

• not found.

BTY-700

This device, like the previous one, is capable of cleaning 3 handpieces at the same time. You can put in it:

• 2 high speed tools;
• turbine high speed handpieces;
• 1 low speed tool;
• handpiece straight, angular or motor.

Among the dental instruments, the most important and demanded are the rotating ones, which indicates the need to provide correct and highest quality care. In addition, they are costly, especially in cases where the dentist prefers options that are produced by world-class companies. The BTY-700 is designed for cleaning such instruments. Its main distinguishing characteristic is that in addition to performing basic tasks, it is able to remove excess oil by blowing it out. However, this does not affect the speed of the device in any way. Processing takes only a few minutes and is performed with the highest quality.

• convenient container for oil;
• an indicator that allows you to control the amount of oil;
• the ability to remove the front panel;
• 750 ml oil included.

• not found.

Handpiece cleaners are similar to each other. When buying them, the main emphasis should be on the number of tools that the device can clean at the same time.