The best ZUBR screwdrivers for 2020

A screwdriver, as a tool for repair or assembly work, is the most popular power tool among citizens of the Russian Federation. The area of ​​application and use is so diverse and varied that there are no such spheres of manual labor where this unit would not be used. The best Zubr screwdrivers will be discussed in this material.

How to choose the right screwdriver?

In order to choose a screwdriver that meets all the requirements of the buyer, you need to know exactly and understand for what purpose it will be used. What should you pay attention to? For certain characteristics declared by the manufacturer, such as:

Power supply for the screwdriver

The efficiency and performance directly depends on the type of power source of the screwdriver. If everything is clear about power supply from a common network, then the issue of batteries should be considered in more detail.

Storage batteries (hereinafter referred to as the battery) have two important characteristics:

1. Voltage. From school everyone knows that according to the formula, the amount of power is directly proportional to the amount of voltage. On sale there are batteries with output voltages: 9.6 V, 12 V, 14.4 V, 18 V. High-power professional screwdrivers can be powered from batteries up to 36 Volts. As you can see, the power of a screwdriver with a 9.6 V battery will not be enough for household work. It is better to choose a battery power supply from 14.4 volts.
2. Capacity. An important characteristic that directly affects the duration of the screwdriver's operation from one battery with a full charge. The capacity is measured in ampere-hours (A * h or A * h). Basically, the capacity value ranges from 1.2 to 2 A * h.

The values ​​of these two very significant characteristics can be applied to the battery case and, without fail, are indicated in the passport and / or operating manual, which is supplied with the screwdriver.

Also, batteries differ in chemical composition. Rechargeable batteries are:

• Nickel-cadmium (Ni-Cd);
• Nickel metal hydride (Ni-MH);
• Lithium-ion (Li-ion).

Some screwdrivers are supplied with an additional rechargeable battery, which increases the operating time of the power tool.

Chuck type

The screwdriver chucks for sale are of two types: keyless and keyless.

The keyless chuck is convenient for manually changing drills or bits. Such cartridges are divided into one- or two-sleeve.The design of the double-sleeve keyless chuck provides for changing the tooling by fixing the lower sleeve with one hand and screwing / unscrewing the upper one with the other hand. And the use of a single-sleeve chuck is made with only one hand, but at the same time, the screwdriver must have the option of fixing the spindle.

The key chuck is equipped with a special key required to change the drill or bit. This attachment is constantly lost sight of, resulting in longer tool change times and longer work times. On the other hand, the use of a key chuck allows the tool to be tightened more tightly than a keyless chuck, which eliminates the possibility of a drill or bit flying out of the chuck.

Accessories

Additional minor criteria for choosing a screwdriver when purchasing may be such as:

• A flashlight built into the body of the power tool, which illuminates the workplace;
• The presence of an additional rechargeable battery in the delivery set;
• The presence of a belt or holster in the package so that the screwdriver is always at hand;
• Adding various sizes of drills and bits;
• Similar accessories.

About ZUBR

The ZUBR company has been a domestic manufacturer of a wide range of high-quality equipment, tools, materials for more than twenty years. Automated and manual tools of the ZUBR company are the most popular among professionals and amateurs in the fields of construction, repair, decoration due to their high quality and reliability.

Reliable and high-quality products of the ZUBR manufacturer are famous outside the Russian Federation. Model lines of products occupy well-deserved places in the world market. That is why the Russian company ZUBR can be proudly called a world manufacturer.

According to the requirements of the modern market, the range of products of the ZUBR company is constantly updated. The modernization of the manufactured models, the expansion of the directions of product exploitation, the research of new technologies, the study of the desires and needs of potential customers take place regularly. As a result, new categories of goods appear at optimal prices.

In order to meet the requirements of competition in the world market with other renowned manufacturers, the ZUBR company is engaged in scientific research to improve the high-tech level of its products. With higher education and extensive experience, engineers are constantly solving problems in the field of development and production. Solving such problems with positive results, undoubtedly, bring a significant contribution to the reliability and quality of manufactured goods. Technical control departments constantly monitor the characteristics of products that must meet the requirements of the modern world.

Ten best models of ZUBR screwdrivers in 2020

10 - drill-driver DA-18-2-Li KNM1

The lightweight model of the ZUBR DA-18-2-Li KNM1 power tool is equipped with a high-tech safety system that protects the tool from overheating, overloading, and discharge. The drill-driver has an excellent weight distribution and a comfortable grip, which provides comfort for productive and reliable work. The two-speed gearbox contributes to the generation of powerful torque. For quick and convenient change of consumable tools, a keyless chuck with one sleeve is used, which regulates a uniform change in a wide range of torque values. There is a backlight on the body of the power tool, which helps in working in places with poor lighting.

• Reverse mode;
• Spindle lock;
• 19 steps of torque regulation;
• 1 hour charging.

• Not found.

9 - drill-driver ZDA-18-2 KIN20

The ZUBR ZDA-18-2 KIN20 drill-screwdriver has sixteen stages of torque control, the maximum of which is thirty-six Newtons per meter. The two speed reducer provides up to four hundred revolutions per minute. The quick-release chuck allows quick tool changes. Two removable NiCad rechargeable batteries, each with an output voltage of eighteen volts, act as power supplies for the instrument.

• Engine brake;
• Additional battery;
• 2 built-in bit holders;
• Illumination built into the body.

• Unreliable strap.

8 - drill-driver ZDA-14,4-2 KIN20

The ZUBR ZDA-14.4-2 KIN20 power tool model is equipped with sixteen steps of torque change, the maximum value of which is thirty-six Newtons per meter. The uniform travel of the two-speed gearbox allows for high quality and reliability in the areas of construction, repair and decoration. The maximum rotation speed of the keyless chuck reaches four hundred revolutions per minute. The power source of the power tool is a detachable 14.4 Volt NiCd rechargeable battery supplied in two pieces. An additional battery provides the possibility of continuous operation of the unit.

• Engine brake;
• 2 batteries;
• Anti-slip grip;
• Backlight.

• Short mains charger cable.

7 - drill driver DA-14.4-2-Li KNM2

The ZUBR power tool with a powerful engine, two removable rechargeable batteries, illumination on the case provides additional comfort when performing construction and repair work. The overheating and overload protection system present in the electronics of the unit allows you to operate the power tool for a long time, without the occurrence of technical problems and breakdowns. The two gearbox speeds perform high torque screwdriving and unscrewing of the fastener, as well as powerful drilling at high rpm.

• Two operating modes;
• Bit socket;
• Fixing the power button.

• The lack of a battery charge indicator on the case.

6 - drill-driver DA-12-2-Li KNM3

Drill-driver DA-12-2-Li KNM3 is supplied with a powerful twelve-volt rechargeable battery, which helps to operate the unit for a significantly long time and without interruption in operation. Electronic safety against overheating, overloading and overloading provides an increase in labor productivity without loss of power of the power tool. It is possible to drill holes in materials of low density.

• Reverse;
• Illumination on the tool body;
• Wide range of torque values.

• One rechargeable battery.

5 - drill-driver DAI-18-2-Li KNM4

The ZUBR screwdriver DAI-18-2-Li KNM4 is a rather powerful and technologically advanced power tool with a removable battery. For convenient and quick tightening and loosening of fasteners, this model has such a characteristic as a torque, the value of which reaches thirty-two Newtons per meter. The screwdriver can be used as a hammer drill for drilling holes in materials of low density: plastic, wood, and so on.

There are nineteen clutch positions, which are located on the tool gearbox and regulate the amount of torque. The design of the screwdriver provides a keyless chuck for fixing drills, bits, crowns with a shank, up to ten millimeters.The set includes two removable batteries with a capacity of 1.5 amperes per hour and a voltage of eighteen volts, a battery charger, a modern design plastic case designed for transporting and storing this power tool.

• Reverse run mode;
• Brushless motor;
• Spindle fixation;
• Charging in 1 hour.

• Unreliable gear shifter.

4 - drill-screwdriver ZSSH-300-2 k

The ZUBR ZSSH-300-2 K power drill-screwdriver is a power tool with the functions of a screwdriver for tightening and unscrewing bolts, screws, self-tapping screws and so on, a hammerless drill - for drilling holes in not very dense materials. The tool is powered with electricity using a network cable from the general network. Power of three hundred watts allows the keyless chuck to reach a speed of one thousand four hundred revolutions per minute. The maximum torque of the unit is thirty-five Newtons per meter. Supplied in a stylish plastic case.

• Reverse mode;
• High power;
• Quick replacement of brushes.

• Mains powered.

3 - drill-driver ZDA-14.4-2

The professional model of the ZUBR ZDA-14.4-2 power tool is equipped with an improved design of the gearbox, which ensures uniform rotation of the chuck with a maximum frequency of one thousand one hundred and fifty revolutions per minute. The chuck is quick-clamping, allowing you to make a quick change of equipment. Sixteen steps of adjustment allows you to set the optimal amount of torque. The removable nickel-cadmium battery supplies electricity to the tool. The body is provided with LED-diode illumination for work in insufficiently lit places.

• One battery holds a charge for a long time;
• High power;
• Sensitive trigger.

• No additional storage battery.

2 - drill driver ZSSH-300-2

This power tool is designed to perform a wide variety of construction work without significant problems. The functions of a screwdriver and a drill make it possible to operate the unit both for screwing and unscrewing fasteners, and for drilling various surfaces. The power supply of the tool is carried out by a network cable from the general network, the length of which is five meters. The maximum torque is thirty-five Newtons per meter. Two speeds of rotation of the quick-clamping type chuck provide up to one thousand four hundred revolutions per minute, which are regulated in twenty-four stages.

• Reverse mode;
• High power;
• Quick replacement of brushes.

• Mains powered.

1 - drill-driver DA-12-2-Li KM1

Drill-driver ZUBR DA-12-2-Li KM1 is the most popular model of power tools among amateurs and professionals in construction, repair and finishing works. The unit is equipped with a keyless chuck that allows fixing a tool with a shank up to ten millimeters in diameter. There is a workstation illumination on the body for the convenience of operating the tool in rooms with poor lighting. The electronics are supplemented with an overheating protection system for the structural elements of the power tool. The hammerless drill function makes it possible to operate the model for drilling holes in materials of low density. The status of the removable twelve-volt battery is indicated by a charge indicator located on the case.

• High efficiency;
• Lack of memory effect;
• Possibility to purchase an additional battery;
• Workplace lighting.

• The only battery.

Outcome

The ZUBR screwdriver is one of the best representatives of Russian manufacturers of power tools on the world market. Which clearly indicates that these products are very reliable and of high quality, meet the requirements of global competition and the wishes of consumers.